Bosch REG-D1 Manuale Utente

INSTALLATION INSTRUCTIONS REG-D1 MAN-REG-D1-03

- 4 - 1. MECHANICAL SPECIFICATIONS–REG D1 (See Section 6 - General Specifications, for more information) Front View Side View Bottom

- 5 - 2. INPUT POWER / VIDEO OUTPUT CONNECTIONS The camera unit is pre-connected with a electrically isolated power board for 12 to 24 VDC/VAC operat

- 6 - 3. MOUNTING SPECIFICATION Caution: Install with appropriate screws to suit mounting surface. Select a suitable location that is protected from

- 7 - The REG-D1 units have a recommended operation range with specified optimal capture distance for each model as shown below. Any number plate re

- 8 - * Optimal distance calculated to allow license plates of 120 pixels wide. Most DVR application can provide readable plates larger than 80 pixel

- 9 - Max 40ْ Figure 5 Maximum Horizontal Angle If the maximum range is exceeded the letters will become smaller and be more difficult

- 10 - 4. COLOR OVERVIEW CAMERA LENS SETTING The following steps show the installer how to access the camera board and the camera lens. Step 4.1 -

- 11 - Figure 6 Rear Housing Removal

- 12 - Figure 7 Housing Separation for Camera, Lens and Voltage Regulator Board Access Lens Loosen len

- 13 - 4.1 Vari-Focal and “Auto-Iris” Control Adjustments Step 4.1.1 - Loosen the lens set screws for focus/zoom adjustments. Step 4.1.2 - T

IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep this instruction. 3. Heed all warnings. 4. Follow all instructions. 5

- 14 - 5. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE LIKELY SOLUTION No Video Power Supply Connections Voltage R

- 15 - Horizontal Scan Lines, Rolling Up or Down Negative, scrambled, or faded image Ground Loop on video cable

- 16 - Poor Color Picture Quality Dim Image Snowy Image (cont’d.) Horizontal Scan Lines, Rolling Up or Down Negative, scrambled, or fad

- 17 - Safety and Precaution “Prolonged direct viewing of the REG-D1 camera product at any distance does not pose a hazard to the retina or corne

- 18 - 6. GENERAL SPECIFICATIONS Power Consumption: 27W Max. Input Voltage: 12 – 24 VDC or 12 – 24 VAC Enclosure (housing): Al

- 19 - Note:

- 20 - Note:

- 21 - Note:

Americas Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 1450, USA Phone: + 1 800 289 0096 Fax: + 1 585 223 9180 security.sale

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the app

IMPORTANT For best results, please read this Instruction Booklet prior to installing the REG-D1 camera. WARNING ! CSA Certified / UL Listed CLASS

NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limits a

INDEX – REG - D1 Camera Description………………………………………………...1 Unpacking………………………………………………...2 Parts List…………………………………………………..2 Items Required for I

- 1 - DESCRIPTION The REG-D1 license plate capture camera unit consists of one IR-sensitive monochrome camera, one integrated panel of Infrared LEDs

- 2 - UNPACKING Care should be taken when unpacking the shipped unit. Check the parts list and confirm all items have been located. Inspect the equi

- 3 - INITIAL PREPARATIONS • Determine the operating voltage at the installation site. The camera‘s Voltage Regulator Board accepts both 12-24VDC/V