Bosch B450 Guida di Installazione Pagina 51
- Pagina / 152
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Item Set Value Remark
Panel Programming Disable Need to set in Web interface.
If set to enable, B450 can be set via the
control panel, the configure method is
same as table 2 or table 3.
If set to disable, B450 cannot be set via
the control panel, only can be set via USB
menu.
Email Server Name smtp.126.com Mail server name
ASCII Code
Email Server Port
Number
465 Mail server port
Email Server
Authentication/
Encryption
Encryption 0 = Basic
1 = Authenticate
2 = Encrypted
Authentication User
Name
[email protected] User Name of Sending Mailbox
Authentication
Password
Solution3000 Password of Sending Mailbox
Configuration steps:
Set the receiver parameters according to Table 1.
If the network module is a B426, log into the B426 Configuration Page, set Panel Programming
to Enable.
Set the network module parameters according to Table 2 and Table 3. The two tables contain
parameters of the outgoing mailboxes.
If the network module is a B450, there are two configuration methods:
– Log in to the B450 menu interface. Set Panel Programming to Disable. Set the parameters
of the outgoing mailbox according to Table 4.
– Log in to the B450 menu interface. Set Panel Programming to Enable. Set the parameters
of the outgoing mailbox according to Table 2 and Table 3.
Notice!
Use well established mailboxes for sending and receiving email (such as gmail).
Do not send more than 6 Emails per hour. The mailbox cannot send or receive Email reports
too frequently since all mailboxes have limitations for the amount of emails they can send and
receive within a certain span of time.
Add the sending mailbox to the receiving mailbox’s approved sender list to prevent emails
from the sending mailbox from being treated as advertising or spam.
Control Panel Configuration | en 51
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Prodotti e manuali riguardandi Sistemi di controllo di accesso Bosch B450
(20 pagine)
(24 pagine)
(96 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale